hdpe dr 9 hdpe pipe pressure rating in vietnam

We Can Supply Them

HDPE Pipe Content

I want to contact Sale Manager : [email protected]


  • Puhui HDPE pipe and fittings

    WL Plastics PE3408 AWWA C906 Water Pipe

    Surge Pressure from Sudden Velocity Change Pipe DR 5.0 fps Velocity Change 1.0 fps Velocity Change 17 56.3 psig 11.3 psig 11 71.9 psi g14.4 psi 9 80.9 psig 16.2 psig Pressure Class, Surge Allowance and Corresponding Sudden Velocity Change For

  • Puhui HDPE pipe and fittings

    HDPE pipes material selection and appliions

    The electro fusion welding of HDPE pipes provides leak-proof joints with weld factor of 0.9 to 1.0, which is a must for appliions like gas distribution. Apart from domestic gas distribution, HDPE pipes are also used for conveyance of coal gas, biogas, compressed air supply etc. Chemical process piping.

  • Puhui HDPE pipe and fittings

    HDPE - Urecon

    Pressure rating of DR 13.5 is 758 kPa 128 psi at 23 C 73.4 F. Insulated pipe available in standard industry lengths of 12.19 m 40 ft and 15.24 m 50 ft; other lengths available on request. Insulation cut back for standard butt fused joint is 230 mm 9 in

  • Puhui HDPE pipe and fittings

    Technical Note PP 816-TN PE3608 & PE4710 Materials Designation Codes and Pipe Pressure Ratings - Hdpe

    Performance Pipe, a division of PO Box 269006 Phone: 800-527-0662 Chevron Phillips Chemical HDPE pipe for sale LP Plano, TX 75026-9066 Fax: 972-599-7348 Pressure Rating PE Materials To understand those requirements a little

  • Puhui HDPE pipe and fittings

    Engineering Recommended & Technical Testing Data Procedures For HDPE Pipe

    dropping the pressure by 10 psi 0.69 MPa. If the pressure then remains within 5% of the target value for 1 hour, this indies there is no leakage in the system. NOTES: • Under no circumstances shall the total time under test exceed 8 hours at 1.5 times the

  • Puhui HDPE pipe and fittings

    HDPE Polyethylene Pipe Fittings | Molded Fittings | Secor

    Molded Fittings. Our molded fittings are available in sizes from 1/2” through 12”, in most wall thickness DR ratings. The molded fittings are available in most common configurations of tees, reducers, short-radius elbows and tapping tees/service saddles.

  • Puhui HDPE pipe and fittings

    PE 3608/3408 IPS HDPE PIPE SIZES - Plastech Plus

    - Other piping sizes or DR''s may be available upon request. - Standard Lengths: 40'' for 2"-24" / 50'' for 26" and larger / Coils available for 3/4"-6"8" by special order Page 1 of 2 DR 13.5 128psi DR 15.5 110psi Pressure Rating DR 7 267psi DR 7.3

  • Puhui HDPE pipe and fittings

    HDPE 4710 - National Pipe

    Scope: This submittal designates the general requirements for High Density Poly-Ethylene Pressure Pipe from compound with a cell classifiion PE345464C as defined in ASTM Standard D-3350. Pipe: All pipe is manufactured in accordance with the specifiions set-forth in AWWA C906 “Standard for Polyethylene PE Pres-

  • Puhui HDPE pipe and fittings

    HIGH DENSITY POLYETHYLENE HDPE PIPE PART 1 GENERAL

    Working Pressure Rating WPR. The pipe shall have a wall thickness dimension ratio DR 11 for pipe 6-inch through 24-inch in diameter. 3. Pipe Identifiion. Each pipe length shall be marked in accordance with AWWA C906 and shall be black in color with4.

  • Puhui HDPE pipe and fittings

    dr 9 hdpe pipe pressure rating in brunei

    The prefix for ASTM D-2239 is SIDR. The most common ratios under this specifiion are SIDR-19, SIDR-15, SIDR-11.5, SIDR-9, and SIDR-7. The lower the SIDR nuer, the Puhui Pipe manufacturer in China HDPE pipes and fittings includes: 1. HDPE Pipe

  • Puhui HDPE pipe and fittings

    Pipe - HDPE, ANSI DR 9.0, IPS in

    21/2/2016· HDPE, ANSI DR 9.0, 250 psi, Pipe Iron Pipe Size in Datasheet. ASTM D3350 - Standard Specifiion for Polyethylene Plastics Pipe and Fittings Materials. ASTM F714 - Standard Specifiion for Polyethylene PE Plastic Pipe DR-PR Based on Outside Diameter. HDPE can provide up to 1.5 times the pipe pressure rating for a recurring surge and up to Puhui Pipe manufacturer in China

  • Puhui HDPE pipe and fittings

    HDPE HDPE PE pipe for water drainage - HDPE100 Pipes

    HDPE HDPE PE pipe for water drainage Despriction: 1. Long working lifespan as min. 50 years. 2. Excellent performance on shock-resistance and low-temperature resistance, brittle temperature could be -70¡ãC. 3. Good Chemistry stability, corrision resistance of

  • Puhui HDPE pipe and fittings

    WL Plastics PE3408 AWWA C906 Water Pipe

    Surge Pressure from Sudden Velocity Change Pipe DR 5.0 fps Velocity Change 1.0 fps Velocity Change 17 56.3 psig 11.3 psig 11 71.9 psi g14.4 psi 9 80.9 psig 16.2 psig Pressure Class, Surge Allowance and Corresponding Sudden Velocity Change For

  • Puhui HDPE pipe and fittings

    HDPE Pipe High Density Polyethylene Pipe 1

    It is the material of choice in harsh chemical environments. HDPE pipe has a smooth ID and maintains its flow capability over time - Hazen Williams C Factor remains 150, even after years of use. HDPE Pipe is Flexible and Fatigue Resistant: HDPE pipe can be bent to a radius 25 times the nominal pipe diameter.

  • Puhui HDPE pipe and fittings

    HDPE 4710 - National Pipe

    Scope: This submittal designates the general requirements for High Density Poly-Ethylene Pressure Pipe from compound with a cell classifiion PE345464C as defined in ASTM Standard D-3350. Pipe: All pipe is manufactured in accordance with the specifiions set-forth in AWWA C906 “Standard for Polyethylene PE Pres-

  • Puhui HDPE pipe and fittings

    HDPE 4710 - National Pipe

    HDPE 4710 HDPE 4710 IPS & DIPS PRESSURE PIPE 14, 16” Pipe Size and Dimensions Page 4 of 6 General IPS DIPS Nominal Size in Metric mm Dimension Ratio DR Pressure Class psi OD Avg. Minimum Wall OD Avg. Minimum Wall 14 350 21

  • Puhui HDPE pipe and fittings

    Engineering Recommended & Technical Testing Data Procedures For HDPE Pipe

    Recommended Testing Procedures For HDPE Pipe Pressure Testing Outside The Trench: • If specified by the engineer, pressure testing may be conducted prior to pipe installation. • After the pipe has been joined, fill it with water, carefully bleed off any trapped air.

  • Puhui HDPE pipe and fittings

    Pipe - HDPE, ANSI DR 9.0, IPS in

    21/2/2016· HDPE, ANSI DR 9.0, 250 psi, Pipe Iron Pipe Size in Datasheet. ASTM D3350 - Standard Specifiion for Polyethylene Plastics Pipe and Fittings Materials. ASTM F714 - Standard Specifiion for Polyethylene PE Plastic Pipe DR-PR Based on Outside Diameter. HDPE can provide up to 1.5 times the pipe pressure rating for a recurring surge and up to Puhui Pipe manufacturer in China

  • Puhui HDPE pipe and fittings

    WL Plastics PE3408 HDPE Pipe – Determining Pressure Ratings for

    Regulations limit the pressure rating to 125 psi for 12” IPS and smaller pipes 100 psi max for >12” IPS through 24” IPS. 4. Determine the long-term pressure rating for DR 11 WL Plastics HDPE pipe on the surface transporting compressed air at 120 F. changes.

  • Puhui HDPE pipe and fittings

    HDPE pipes high density polyethylene pipes and

    HDPE pipes and fittings includes: 1. HDPE Pipe, Pressure rating: SDR 41 - SDR 6, with size from DN16mm - 1600mm. 2. HDPE Butt Fusion fittings, Pressure rating: SDR 41 - SDR 6, with size from DN63mm - 1600mm. 3. HDPE Electrofusion fittings, Pressure

  • Puhui HDPE pipe and fittings

    There is no alternative for PE pipes in natural gas networks for their high security levels. The medium density polyethylene MDPE PE 80 yellow colour are used up to 5.5 bar according to PL2 - 1. GM HDPE PE 100 pipes with orange color are used with working pressure up to 7.0 Bar according to PL2 - 8.

  • Puhui HDPE pipe and fittings

    MAB PE4710 mechanical products for HDPE pipes - Plastics Pipe

    Pressure Rating: DR 32.5 65psi DR 26 80psi DR 21 100psi DR 17 130psi DR 13.5 160psi DR 11 200psi DR 9 250psi take in consideration pressure class of fitting. DR 7 335 psi take in consideration pressure class of fitting.

  • Puhui HDPE pipe and fittings

    Technical Note PP 816-TN PE3608 & PE4710 Materials Designation Codes and Pipe Pressure Ratings - Hdpe

    Performance Pipe, a division of PO Box 269006 Phone: 800-527-0662 Chevron Phillips Chemical HDPE pipe for sale LP Plano, TX 75026-9066 Fax: 972-599-7348 Pressure Rating PE Materials To understand those requirements a little

  • Puhui HDPE pipe and fittings

    Fortiline|10" DR9 HDPE PIPE IPS

    Pipe; Nominal Pipe Size 10 Inch; Schedule DR 9; Thickness 1.194 Inch; Length 40 Foot; End Connection IPS; Material HDPE; Material Specifiion ASTM F714/D3035; Finish Black; Pressure Rating 250 PSI; Temperature Rating 140 Deg F; liion Potable Water, Sewer, Drain, Mining, Irrigation and Reclaimed Water; Weight 15.68 Pound per Foot;

  • Puhui HDPE pipe and fittings

    HDPE Fittings and Equipment Product alog - Hdpe Supply: Hdpe Fittings, Electrofusion, Polyethylene Pipe…

    SDR 9 Standard Dimension Ratio 255 PSI Working Pressure at 73.4˚ F Nominal IPS Pipe Size A inches B inches C inches D inches E inches Weight lbs. Item Code 2” 4.25 2.95 0.26 2.38 5.44 1.00 90BI-2IPS-9 3” 5.91 4.06 0.39 3.50 7.66 2.00 90BI-3IPS-9

  • Puhui HDPE pipe and fittings

    Fortiline|8" DR9 HDPE PIPE IPS

    Pipe; Nominal Pipe Size 8 Inch; Schedule DR 9; Thickness 0.958 Inch; Length 40 Foot; End Connection IPS; Material HDPE; Material Specifiion ASTM F714/D3035; Finish Black; Pressure Rating 250 PSI; Temperature Rating 140 Deg F; liion Potable

I Need the Best Price(Quotation)